Good work! You have framed the area you are finishing. The walls and ceiling have been packed with soundproofing, fire retardant, insulation, or some combination thereof. Electrical outlets, overhead lighting, surround sound speakers, etc., have been installed. Now, you are ready to hang the drywall. Hanging and finishing drywall is the topic of this post. As with earlier posts, I refer you to videos on YouTube to help you understand the basics of hanging and finishing drywall. This post will present thoughts and considerations you may not find in those videos. Probably the most important point to consider is that the fewer joints to mud and tape the better.

Key Discussion Points

• • Plan out your cuts (fewest joints to tape)
  • Which size sheets can you accommodate?
  • Finishing corners
  • Taping
  • Hanging sheets, vertical vs horizontal
  • Fixing damaged sheets (torn paper)
  • Benefits of Expansion Foam

Your first task is to determine the optimal drywall sheet size to purchase. Our basement is a walk-out with three access points and relatively high ceilings. If you have a captured basement with lower ceilings or tight stairwells you may be restricted on the sheet size you can use. Otherwise, you may have to cut your sheets before moving them into the basement. So, ceiling height and accessibility must be evaluated before a buying decision is made. Try to purchase the largest sheet size possible to minimize cuts, The determining factor will be the type of basement you are finishing.

When my husband was ready to install drywall, he was confident he could hang and finish the walls. He was uncomfortable with the ceilings, so he hired professionals to tackle that task. In effect, he did that job backward, walls first then ceiling. The recommended installation process is ceilings first. The outcome was fine. No problems were encountered following this sequence. As most of the construction area has nine-foot ceilings we used nine-foot sheets hung vertically. The remainder of the area had eight-foot ceilings so we could place 8-foot sheets horizontally.

Corners can be tricky. External corner joints can be managed using corner beads, but they can be challenging, depending on the connection. Internal corners may have gaps that need to be corrected. If Internal corner gaps are large, expansion foam can be the solution. The foam will fill the gap and provide a base to add the joint compound. My husband had to deal with both situations. For an amateur, he did well. However, he plans additional work on one external corner.

Exposing electrical outlets is your next task. From my experience, one achieves the best result by using a drywall router tool. This tool rides along the exterior of the outlet box as it cuts away the drywall. If you don’t have a drywall router tool, you can measure and mark the outlet box location on the drywall. You can cut before or after the drywall is hung. Of course, this method requires meticulous measurements to ensure the cut matches the outlet’s location. My husband found this method more challenging. It required additional time and effort to correct errors in the cut.

Many YouTube videos describe how to mud, tape, and finish your drywall. Again, I refer to those videos for a better understanding of this task. I want to emphasize our learning to ensure a smooth, attractive joint. The first consideration is the joint compound to use. My husband used a premix joint compound for our basement finishing project. If you ask him today, however, he will say he wished he had purchased a dry product to mix himself. His thinking is that the premix resulted in too much sanding and was more difficult to achieve a smooth finish. The other point he makes is to wet the tape before its application to the joint. Many videos he watched did not emphasize this point, possibly because they used a wetter mix. He quickly learned that wetting the drywall tape was mandatory when using the premix joint compound. Not doing so resulted in bubbles and separation of the tape from the drywall.

Summary and Conclusion

Begin your drywall installation with a plan. Know the square footage you intend to cover and your options for different sheet sizes. Determine if you have any constraints moving drywall sheets into your work area. That information may determine the size of the drywall sheet you must buy. Remember, you want to minimize the number of joints to finish. The joint compound you choose is an important consideration. Finishing internal and external corners can be improved using corner beads and expansion foam. Making the cutouts for electrical outlets is best done with a drywall router. That tool will give you a clean and accurate cut, and minimize any further work on outlets.

 

Jim Weber – Managing Partner,  ITB Partners;

President, New Century Dynamics Executive Search

I hope you enjoyed our perspective and would like to receive regular posts directly in your email inbox. To this end, please put your contact information on my mailing list.

Your feedback helps me continue to publish articles that you want to read.  Your input is important to me, so please leave a comment.

Installing Drywall – Your Basement Finishing Project

Good work!  You have framed the area you are finishing. The walls and ceiling have been packed with soundproofing, fire retardant, insulation, or some combination thereof. Electrical outlets, overhead lighting, surround sound speakers, etc., have been installed. Now, you are ready to hang the drywall. Hanging and finishing drywall is the topic of this post.

https://wp.me/pa0WEz-33B